The Conclusions and Recommendations may be combined or, in long reports, presented in separate sections.

Conclusions and recommendations

If there are no recommendations to be made as a consequence of the project, just call this section Conclusions.

The Conclusions section sums up the key points of your discussion, the essential attributes of your design, or perhaps the significant outcomes of the investigation. As its function is to round the story off of assembling your shed, it must:

  • be written to relate right to the aims of this project as previously mentioned when you look at the Introduction
  • indicate the extent to which the aims have been achieved
  • summarise the findings that are key outcomes or information in your report
  • acknowledge limitations and make recommendations for future work (where applicable)
  • highlight the significance or usefulness of your work.

The conclusions should connect with the aims regarding the work:

The aim of this project is to design a mobile phone tower for a suburban location..

The cellular phone tower presented here could be erected safely in a suburban street.

It needs a total area of no more than 2m 2 l, and contains the following safety features.

This investigation will review the amount of passengers utilizing the Monash University Clayton-Caulfield inter-campus bus so that you can recommend adjustments into the ongoing service if required.

Analysis regarding the survey data obtained in this project demonstrates that use of the Clayton-Caulfield inter-campus bus has increased by 24% in the past 5 years. It is recommended that frequency be increased during peak usage.

The Conclusions section below is from a known level 2 Civil Engineering Alternative Designs report presenting two designs for a an overpass bridge. Click on the coloured buttons to begin to see the comments.

Conclusions

All the two bridge designs Lecturer’s comment:
An elegant beginning for a Conclusions follows on neatly from the preceding discussion. In this full case, it also indicates that the aims regarding the project have been met. presented in this report fulfil the criteria specified in the project brief. Both designs Lecturer’s comment:
The main findings or outcomes – in this full case the important thing options that come with the designs – are then recapped. Incorporate piers that are round piled foundations, that are used since the soil conditions are unknown and possibly unstable. Design 1, a simple composite I-girder bridge, has the benefit of being made from steel and therefore has longer spans and fewer piers.

Design 2, a beam that is super-T >Design 2 Lecturer’s comment:
The need for the outcome – in this instance the ultimate recommendation – is clearly stated. is therefore recommended. It offers Lecturer’s comment:
To finish off, the achievement associated with project is reinforced. An write my paper overpass that is affordable superior durability, and fully meets what’s needed for the design brief.

Always address limitations and suggest how they may be overcome in the future work. The below that is excerpt from the Conclusions of a report on a project investigating the end result of pulsation on heat transfer in horizontal pipe flow.

Experimental results Lecturer’s comment:
Key conclusions drawn through the project. indicated that pulsed flow without flow reversal had no effect that is significant with steady flow. Preliminary experiments with reversed flow, however, clearly indicated increased heat transfer. This is likely due Lecturer’s comment:
Provide a explanation that is possible notable results, especially unexpected ones. to your large disturbances within the hydrodynamic boundary layer once the flow changes direction. Further research Lecturer’s comment:
Recommend further research to address any extra work you think will be useful. is preferred to determine the maximum achievable enhancement.

It should be noted that Lecturer’s comment:
Acknowledge limitations or errors and suggest explanations and/or solutions. the experimental results try not to concur with the theoretical equations. This may be as a result of the deposits which developed within the pipe, or even to inconsistent thermocouple temperature. Therefore, regular inspection regarding the test rig is advised.

For a rather report that is long it is acceptable to provide the conclusions and recommendations in point form:

The prototype robot courier presented here has been confirmed to be capable of delivering documents autonomously in an office environment. It has demonstrated the next aspects of mobile robotics:

  1. Localisation: The Kalman localisation that is filter-based achieved sub-centimeter accuracy under normal operating conditions.
  2. Environment modelling: The occupancy map was updated dynamically to add obstacles not contained in the original map.
  3. Path planning: A distance path that is transform-based using obstacle transforms produced a globally optimal local entrapment-free path to the target.